Buying second-hand appliances is a reasonable way to furnish a home, and plenty of used machines have years of good service left in them. The problem is that the faults which matter most are the ones you cannot see from the front — and a seller standing beside you rarely volunteers them.
This is what we check when we look at a used appliance. None of it needs tools, most of it takes under twenty minutes, and it catches the majority of the machines that turn into a repair call within the first month.
Before you go: two things to ask
Ask for the model and serial number in advance. It takes the seller thirty seconds to photograph the data plate — inside the door frame, behind the kick plate, or on the back panel. With that number you can check whether parts are still made for that platform, which decides whether the machine is repairable at all when something eventually goes.
Ask why they’re selling it. Renovation, moving, upgrading to a larger size — all normal. Vague answers, or “it just needs a small part,” deserve more weight than people give them. A machine being sold because of a fault is not automatically a bad buy, but you want to know which fault before you load it into a truck.
One more thing worth doing before the visit: measure your space, your doorways and the narrowest turn on the route. A machine that can’t get into the room is a problem no inspection catches.
Checks that apply to every appliance
Start with these regardless of what you’re looking at. They take five minutes and they rule out a surprising number of machines.
- Make it run. Not “it worked last week” — plugged in, running, in front of you. A seller who can’t demonstrate the machine is asking you to buy a story. If it’s disconnected, ask to plug it in somewhere, even briefly.
- Look at the back and underneath. This is where the evidence lives: rust at the base, water staining, crushed hoses, hacked-up wiring, missing panels, repairs done with tape.
- Check the floor underneath. A dry outline where the machine has been tells you one story; a stained or corroded patch tells you another.
- Smell it. Burnt electrical smell, persistent mildew, or heavy chemical cover-up scents are all worth asking about.
- Open and close every door. It should swing, seat and seal cleanly. Hinges that sag or doors that need a shove are wear you’ll pay for later.
- Check the cord and plug. Nicks, scorch marks, tape repairs, or a plug that doesn’t match a standard receptacle.
- Press the buttons. Every one. A display with dead segments or a touch panel that needs several presses is usually a control board, and control boards are what end an appliance’s life well before anything mechanical wears out.
Washing machines
The washer is the one most worth inspecting carefully, because its most expensive failure is also its least visible.
Spin the drum by hand. It should turn smoothly and quietly. Grinding, rumbling, or a gritty feel means bearings, and on most front-loaders that repair costs enough that it decides the machine’s future.
Grab the drum and rock it. Take hold of the top and bottom of the drum opening and pull. A small amount of give is normal; obvious knocking or clunking is not — that’s worn suspension or a failing bearing housing.
Check the door seal on a front-loader. Pull the rubber boot back and look inside the fold. Black mould, tears and trapped debris all live there. A seal is replaceable, but heavy mould also tells you how the machine was looked after.
Look at the drum interior for scale. A chalky white film on the drum and heater area means it ran on hard water, which matters a great deal if the machine is coming from a rural property. We cover why in hard water and well water damage to appliances in southeastern Manitoba — scale shortens the life of everything it touches.
Run a short cycle if you can. Listen through fill, agitation, drain and spin. Each stage sounds different, and a noise that only shows up on spin usually points at the bearings — the same pattern we describe in what a loud noise during the spin cycle actually means.
Look behind for water trails. Dried mineral tracks down the back panel mean it has leaked at some point, and where a washer leaks from tells you what failed.
Dryers
Spin the drum. Same test as the washer. A rumble or a regular thump as it turns is drum rollers or bearings.
Pull out the lint filter. Clear the lint and run it under a tap if you can. Water that pools on the mesh instead of passing straight through means a residue film from fabric softener, and that film has been choking airflow for a long time.
Look inside the lint housing. Packed lint deep in the cavity means the machine ran restricted, which means it ran hot. Heat is what ages a dryer.
Check the drum seal. The felt ring at the front and rear of the drum. Compressed, torn or missing felt lets hot air escape past the drum.
Confirm it’s electric and check the cord. We don’t work on gas dryers, and an electric dryer needs a 240-volt receptacle that matches its cord — three-prong and four-prong are not interchangeable. If your laundry room isn’t set up for it, what needs to be ready before a washer or dryer install covers what has to exist first.
Refrigerators and freezers
It has to be running when you arrive. This is non-negotiable and it’s why you arrange the visit in advance. A fridge that’s been unplugged “for the move” tells you nothing at all. Cold takes hours, so a cabinet that was switched on when you walked in can’t be faked.
Put your hand in both compartments. The freezer should be properly cold and the fridge section noticeably cool. A warm fridge with a working freezer is usually airflow rather than a dead compressor, but it’s still a repair.
Listen to the compressor. A steady hum is right. Clicking on and off every few minutes, or a loud knocking, is not — and different fridge noises mean quite different things.
Do the paper test on the seals. Close the door on a sheet of paper and pull. If it slides out with no resistance, the gasket isn’t sealing and the compressor has been running longer than it should for a long time.
Look at the back. Condenser coils thick with dust and pet hair mean the unit has been shedding heat badly for years.
Check for frost patterns. Heavy ice on the freezer’s back wall, or ice around the door frame, points at a defrost system fault or a seal that lets humid air in.
If it has a dispenser, run it. Weak flow, hollow or undersized cubes usually mean a restricted water line or a tired valve.
Dishwashers
Pull the filter out of the base of the tub. It twists out. What’s in it tells you how the machine was maintained better than anything the seller says.
Inspect the tub for rust. Surface marks on racks are cosmetic. Rust on the tub itself, especially at the base or around the heating element, is structural and it doesn’t get better.
Spin the spray arms. They should turn freely. Hold one up to the light and look at the holes — mineral deposits narrowing them is a hard-water sign.
Check the door hinges and springs. Open the door fully and let go. It should hold position rather than dropping. A door that falls open has stretched springs or worn cables.
Ask whether it drained properly. Standing water in the base is the most common fault we’re called out for, and what actually blocks a dishwasher drain ranges from a five-minute fix to a failed pump. Worth knowing which before you buy.
Ranges, ovens and cooktops
Turn every element on. Coil elements should glow evenly across the whole spiral. On a glass top, watch for zones that heat in patches or not at all.
Heat the oven. Set it to a moderate temperature and give it fifteen minutes. It should reach heat and hold it. If you can bring an oven thermometer, better still.
Examine the glass top closely, at an angle. Chips, cracks and deep scratches on ceramic glass are not repairable — the top is replaced, and on many models that costs a meaningful share of what the appliance is worth.
Check the oven door seal and hinges. The gasket should be intact all the way round, and the door should hold whatever position you leave it in.
Confirm the anti-tip bracket situation. A freestanding range needs one, and it’s rarely included with a second-hand sale. Plan for it.
Electric only, and check what your kitchen has. If you’re switching from gas, there’s almost certainly no 240-volt circuit in that wall. Built-in ovens and cooktops also need exact cabinet openings — what your kitchen needs before a range, oven or cooktop install goes through the measurements that have to match.
Microwaves and range hoods
Heat a cup of water in the microwave. A minute should make it properly hot. Lukewarm after that means the magnetron is weak, and on a used unit that’s usually the end of the story — our guide to whether it’s worth repairing a microwave explains why.
Check the microwave door closely. Bent frame, damaged latches, or a door that doesn’t sit flush. These are the safety components, and a microwave with a compromised door seal isn’t a bargain at any price.
Run the hood fan on high. Listen for bearing noise from the motor, and check whether the grease filters are present and in reasonable condition. Weak extraction may be the duct in its old home rather than the unit, but a hood that doesn’t vent properly has several possible causes and you can’t tell which from a driveway.
When to walk away
Some findings aren’t worth negotiating over.
- Rust through the tub or cabinet on a washer or dishwasher — structural, not cosmetic
- Cracked ceramic cooktop glass
- Any burnt electrical smell, or scorch marks around terminals and connections
- A fridge that wasn’t running when you arrived, with no good reason offered
- Visible amateur repairs — taped wiring, mismatched parts, missing screws holding panels on
- A microwave with door or latch damage
- No model number available, or a model whose parts are no longer made
- A seller who won’t let you run it
What we see on service calls
A few patterns come up often enough across Winnipeg, Transcona, Steinbach, Lorette and the surrounding communities to be worth naming.
Bearing noise gets sold as “it’s just a bit loud.” It isn’t. A rumbling drum is the single most common reason a used washer becomes an expensive mistake, and it’s audible in ten seconds if you spin the drum by hand.
Machines from well-water homes arrive pre-aged. Scale on elements, narrowed spray arms, clogged valve screens. The appliance may be eight years old and in the condition of a fifteen-year-old one.
Control panel faults get blamed on the user. “You just have to press it twice.” That’s a failing board or touch membrane, and it won’t improve.
Nobody checks the space before buying. We’re regularly called to install a second-hand appliance into a spot that has no suitable outlet, no vent, or an opening of the wrong size. The machine was fine; the kitchen wasn’t ready.
If you’ve found something and want a second opinion before the money changes hands, the model number and a description of what you noticed are usually enough for us to tell you what you’re looking at. And once it’s home and the space is ready, you can book an installation online.
Frequently asked questions
Is buying a used appliance a bad idea?
No. Plenty of second-hand machines have years of service left. The risk isn’t the fact that it’s used — it’s buying one without running it and looking behind it first.
How old is too old?
Age matters less than condition and parts availability. A well-kept eight-year-old machine from a two-person household can be a better buy than a four-year-old one that ran six loads a day on hard water. The model number tells you whether parts still exist, and that’s the question that decides whether it can be repaired at all.
What’s the single most important check?
Seeing it run. Everything else is secondary. A seller who can’t or won’t demonstrate the appliance is the clearest warning sign there is.
Can I inspect an appliance that’s been disconnected for a move?
Partly. You can check the drum, seals, hinges, panels and the back of the machine. You cannot confirm that it heats, cools, drains or spins — and those are the expensive failures. For a fridge or freezer especially, arrange to see it running.
Should I worry about scale on a machine from outside the city?
It’s worth factoring in. Rural properties on private wells have much harder water than the city supply, and the mineral buildup that comes with it shortens the life of heating elements, valves and pumps. It doesn’t rule a machine out, but it does mean the appliance has aged faster than its years suggest.
Do you install appliances that were bought second-hand?
Yes, provided they’re electric and the space is ready — correct outlet, water and drain where needed, and a vent duct for a vented dryer. We connect, level, secure and test; we don’t run new circuits, plumbing or ductwork.
Can you inspect an appliance before I buy it?
Not at a stranger’s home, no. But if you send us the model number and tell us what you noticed, we can usually say whether what you’re describing is a minor fault or the kind that ends a machine.